Description
Compact and lightweight, AIR10 active loudspeakers provide a rich, extended low-end and natural high-frequency extension in an enclosure that will easily fit in the backseat of a small car. Backed by 1,200W (dynamic) of Class D/Class AB power and enhanced with easy-to-use digital tuning functions, the AIR10 gives you all the power and tools you need for both mobile and installed sound.
 
Each type of power amplifier has advantages and disadvantages. By employing different amplifier types for each driver, AIR10 loudspeakers use the respective strengths of Class D and Class A/B amplifiers to provide optimal response throughout the speaker’s frequency range. A 500W (continuous), Class D amplifier powers the 10-inch low-frequency driver, providing efficient, clean low end when you need it. A 200W (continuous), Class AB amplifier powers the 1-inch high-frequency driver, delivering a natural sounding, “AIR-y” high end. The combination can deliver up to 121 dB SPL of sweet, clear sound between 66 Hz and 20 kHz.
 
The AIR10 loudspeaker is equipped with an easy-to-use signal processor that makes it simple to customize your loudspeakers with the push of a button. Presets customize the AIR10’s response for use as front-of-house mains; as monitor wedges; for music playback (e.g., for DJs); for enhanced low end and a warmer sound; and for improved speech intelligibility. Treble and bass controls let you boost or cut by 10 dB to compensate for room anomalies. Location presets let you optimize performance for stand and bracket mounting as well as flown installations.
The AIR10’s molded plastic cabinet can be mounted in several ways, providing tremendous versatility. The multi-angle enclosure sports nonskid rubber feet on the bottom for upright front-of-house use and nonskid rubber feet on one side for stage monitor applications. Rig the speaker using M10 fly points or ground-stack it for portable applications. Mount it on a tripod or atop an AIR-series subwoofer using an optional sub pole. The integrated dual-position pole mount lets you aim the speaker level or at a 7.5˚ downward tilt. And the AIR10 is easy to transport, thanks to its top-mounted handle.
If you place a loudspeaker against a hard surface such as a wall or floor, the low frequencies emitted from the rear of the enclosure propagate back into the room. This effect, called “half-space loading,” can increase the output of bass frequencies by as much as 6 dB, and it is an unavoidable issue with floor monitors. Most PA speakers in this class simply roll off excess low frequencies with a highpass filter—a half-baked compensation for half-space loading. In contrast, AIR-series full-range loudspeakers offer a Monitor preset that uses DSP to retune the speaker to both compensate for bass buildup and maintain a tight mid-bass response, while suppressing problematic frequencies to reduce feedback.
​
AIR-series full-range loudspeakers offer a choice of inputs so you can use them with a variety of sources. You get two combo XLR mic/TRS line inputs, each with a Class A microphone preamplifier and independent gain control. A stereo 1/8” connection admits signals from smartphones, tablets, and other consumer audio devices. These signals can be combined with the AIR10’s internal mixer, and a balanced XLR Mix output lets you send pass the signals to other AIR-series loudspeakers.
 
Main Components
Hybrid “best of both worlds” 1,200W (peak) power amp configuration:
Low-frequency driver: 900W, Class D amplifier
High-frequency driver: 300W, Class A/B amplifier
Maximum SPL 121 dB peak
1-inch, high-frequency compression driver
10-inch woofer with a 2-inch voice coil
66 Hz to 20 kHz frequency response
121 dB SPL (max)
90° x 60° (horizontal x vertical) dispersion pattern
Onboard mixer with two combo XLR and ¼” inputs and one summed balanced output
 
Controls
Easy-to-use DSP performance presets:
DJ—music playback
FOH—normal front-of-house o Enhance – enhanced low end for a warmer sound
Monitor – optimized for floor wedge placement
Speech—applications where speech intelligibility is critical
Additional presets and controls:
Stand—for mounting on a pole or tripod
Bracket – for wall-mount applications
Suspend – for suspended applications
 
Convenience Features
Multi-angle enclosure for mains or monitor-wedge applications
Comfortable ergonomic handle
35 mm pole socket with 7.5˚ downward tilt
M10 rigging points for suspended installation
Defeatable front-panel LED
Rugged plastic enclosure
Tour-grade, 1.2 mm steel grille
 
Acoustic Performance
 
Configuration
Active 2-way
Frequency Range (-3 dB)
66 Hz to 20 kHz
Frequency Range (-10 dB)
55 Hz to 20 kHz
Crossover Frequency
2.2 kHz
Maximum Output
121 dB SPL
Nominal Dispersion (HxV)
90˚x 60˚
Transducer
 
LF Driver
10” (2” voice coil)
HF Driver
1” compression
Amplifier
 
Amplifier Type
Class D (LF), Class AB (HF)
Total System Power
1,200W (Peak)
LF Power
900W
HF Power
300W
Connections and Controls
 
Inputs
2 x XLR/TRS mic/line combo; 1 x 1/8” TRS stereo
Outputs
1 x XLR Mix Out
DSP
 
DSP Features
LCD screen with EQ and multiple presets
Enclosure
 
Cabinet
H-PP molded
Grille
1.2 mm steel
Handles
1 top
Flypoints
2 top, 1 back
Pole Mounting
Dual position (0˚, 7.5˚)*
Dimensions (H x W x D)
20.3″ x 11.8″ x 11.5″ (516 mm x300 mm x 291 mm)
Weight
28.7 lbs (13 kg)
Power
 
Power Input
115V / 230V ~50/60 switchable
Maximum Current
2.3A (230V-50 Hz), 4.6A (120V)
*AIR Speaker mounts are compatible with M20-threaded screw poles with a diameter of 33 mm and a length of 31.5″